---
title: "Yamaha KT100 data analysis for club racers – Slicks"
description: "An air-cooled KT100 has no radiator to hide behind. Check its exhaust temperature against 500–600 °C and find the tenths a spec class is won by."
url: "https://slicks.app/use-cases/yamaha-kt100-data-analysis"
updated: "2026-11-12"
---

[Use cases](https://slicks.app/use-cases)

For the Yamaha KT100

# Data for an engine with no water to read

On an air-cooled KT100 the exhaust temperature is the engine's one warning light. Slicks checks it after every session, and shows where the lap went when everyone has the same engine.

[![Download on the App Store](https://slicks.app/app-store-badge.svg)](https://apps.apple.com/ca/app/slicks/id6746713889?mt=12)[![Download on the App Store](https://slicks.app/app-store-badge.svg)](https://apps.apple.com/ca/app/slicks/id6746713889)

Free for iPhone, iPad and Mac

![Slicks on an iPhone showing a kart session: its fastest lap drawn on a map of the track in the colours of its speed, the lap time, and the session's laps underneath.](https://slicks.app/hero/phone-640.webp)

Slicks opens the MyChron file from a Yamaha KT100 kart and checks the session's peak exhaust temperature against 500–600 °C, the window it uses for the KT100, in plain words as well as colour. There is no water window, because the engine is air-cooled. Peak RPM is shown without a verdict, and the laps, sectors and corners are read as for any engine.

## The KT100 and the racing it does

The KT100 is Yamaha's 100 cc, air-cooled, piston-port two-stroke. It is a club and spec-class engine: raced in Yamaha classes in North America, in clubman classes in Australia, and in junior classes that often run it with a restrictor to slow it down. It is cheap to run and simple to look after, which is why so many drivers start on it and why some never leave.

Spec racing changes what data is for. When the whole grid runs the same engine to the same rules, horsepower is mostly off the table. What is left is the driver, the kart and keeping the engine healthy enough to finish. A tenth is a lot of places in a class like that, and most of it is found in corners, not in the engine.

## Why an air-cooled engine needs watching differently

A water-cooled engine has a radiator between it and the weather. You read the water temperature, add or peel tape, and the engine settles. A KT100 has none of that. Its temperature follows the jetting, the airflow over the cylinder and the day's air directly, and there is no gauge to tell you it is getting too hot until it is.

That makes the exhaust temperature the reading that matters. Too hot usually means lean, and on an air-cooled two-stroke lean is how pistons get hurt. Too cold usually means rich and slow. Slicks reads the peak from your logger's exhaust channel and tells you whether it sat in the window.

| Reading                      | The window Slicks checks against | What you get                  |
| ---------------------------- | -------------------------------- | ----------------------------- |
| Peak exhaust gas temperature | 500–600 °C                       | A verdict in words and colour |
| Water temperature            | none (air-cooled)                | Not checked                   |
| Peak RPM                     | none                             | The number, without a verdict |

The 500–600 °C window is the range the karting community quotes for the KT100, and it sits lower than the windows quoted for the water-cooled 125s. It is not Yamaha's specification. If your engine builder gives you a range, theirs wins, and Slicks has no custom windows, so read the number when the two disagree.

One thing to check on your own kart: many air-cooled engines carry a temperature sensor under the spark plug instead of a probe in the exhaust. A cylinder-head reading is a different temperature, and the exhaust window is not the one to judge it by. Slicks tells the two apart by the reading alone: any temperature that peaks above 200 °C is checked against the exhaust window. So if your head sensor runs that hot, ignore the verdict beside it, read the number, and ask whoever built your engine what theirs is for that sensor.

## Tracking the temperature through a hot day

Air-cooled engines feel the weather more than anything else on the kart. A jetting that is right on a cool morning can run hot by mid-afternoon. A practical way to keep track:

1. Look at the exhaust verdict on the Setup page after every session, not only when something feels wrong.
2. When it moves towards the top of the window, open the fastest lap and chart the exhaust temperature against distance. See whether it climbs along the longest straight or spikes in one place.
3. Note the change you make (a carb adjustment, usually) in the carb field of the next session's setup, so the peak that follows sits on the same page as the change.
4. Write the air temperature or "hot, sunny" in Notes. Slicks does not record the weather, and the number means more next to it.

Every channel your logger recorded also appears on the Setup page as its lowest and highest reading for the session, so a second temperature sensor is there to read too.

## Finding time when the engines are equal

With little power to play with, a KT100 lives on corner speed. Speed lost at the apex comes back slowly on an engine this size, so a small mistake costs you down the whole straight after it. That is what the **Time Loss** page is for. It lines every lap up against your fastest and ranks the corners that cost the most, with the tenths lost, how much slower the slowest point was, and whether the braking point moved earlier or later.

On a KT100, watch the minimum-speed column most. A corner where you lose two or three km/h at the slowest point is usually worth more than one where you braked a few metres early. Tap it to race the worst lap there against your fastest in Compare, and look at where the gap starts to grow.

Then check consistency on the Laps page: how many laps were within half a second of your best. In a spec class that number often says more about the result than the best lap does. Our page on [lap time consistency](https://slicks.app/use-cases/kart-lap-time-consistency) goes further into it, and [club karting data analysis](https://slicks.app/use-cases/club-karting-data-analysis) covers a club race day from start to finish.

## Gearing and RPM without a window

Slicks does not judge the KT100's revs, but it records the peak and charts RPM along every lap. Use it by comparison: log the sprocket teeth in the session's setup, change one tooth, and see where the RPM trace ends up at the end of the longest straight in the next session.

What Slicks does not do for a KT100 racer: it has no window for a cylinder-head temperature and no custom windows, it reads only AiM XRK and XRZ files, and compares laps within one session rather than across sessions.

## Slicks at a glance

- **Files:** XRK and XRZ, as AiM loggers write them, parsed on the device
- **Devices:** iPhone, iPad and Mac, one app, one library
- **Requires:** iOS 26.6, iPadOS 26.6 or macOS 26.4
- **Price:** Free on the App Store
- **Sync:** Every device you sign in on; the summary works offline

Updated 12 November 2026

## What Slicks shows

_Figure: Engine speed round lap 8 at Adria Kart, standing on the track as a fence as tall as the revs, peaking at 14,114 rpm._

### Engine

Peak RPM, exhaust and water temperatures against your engine’s window.

_Figure: Adria Kart from above with lap 8's line on it, green where it gained on lap 4 and red where it lost to it, the stretches that cost the most numbered in order._

### Where the time went

The corners that cost you the most time, ranked by loss, with the braking point and minimum speed.

_Figure: Adria Kart from above in three sectors, each in turn lifted out of the track with its time and its speed line drawn on it._

### Sectors

Every lap split into sectors against the session’s best, and the theoretical best they add up to.

## Questions

### Why is there no water temperature window for the KT100?

Because the KT100 is air-cooled and has no water to measure. Slicks checks its exhaust temperature against 500 to 600 °C and shows any other temperature your logger recorded without a verdict.

### Is 500 to 600 °C Yamaha's specification?

No. It is the range the karting community quotes for the KT100, and the window Slicks checks against. If your engine builder works to different numbers, go by theirs.

### My KT100 has a temperature sensor under the spark plug, not in the exhaust. Does the window apply?

Not really. A cylinder-head sensor reads a different temperature from an exhaust probe, so judge it by the numbers your engine builder gives you for that sensor rather than by the exhaust window.

### Can I see what RPM my KT100 reached?

Yes. The Setup page shows the session's peak RPM, without a verdict since the KT100 preset has no RPM window, and the lap screen charts RPM against distance for any lap.

### Does Slicks work with older loggers that a lot of Yamaha karts still carry?

Only with AiM loggers that write XRK or XRZ files, such as the MyChron 5, 5S and 6\. It does not read RaceStudio 2 files, Alfano or other brands' data.

## Read next

[Everything Slicks is for](https://slicks.app/use-cases)

- [For club racersPractice, qualifying, heats and the final: what to read in your AiM data at each stage of a club race weekend, and how to track every change you made.](https://slicks.app/use-cases/club-karting-data-analysis)
- [EGT and water temperatureSee your kart's exhaust and water temperature peaks against the engine's window, colour the track by EGT, and log carb and radiator changes.](https://slicks.app/use-cases/kart-egt-and-water-temperature)
- [IAME KA100Read an IAME KA100 session on iPhone, iPad or Mac: exhaust temperature against a 580–650 °C window, the RPM trace, and the corners that cost you time.](https://slicks.app/use-cases/iame-ka100-data-analysis)
- [Lap time consistencyHow consistent was that session? Slicks gives the spread of your lap times and how many laps were within half a second of your best, from any AiM file.](https://slicks.app/use-cases/kart-lap-time-consistency)

![The Slicks app icon](https://slicks.app/app-icon.webp)

## Bring a session file

Download it and open one of your XRK files: your laps draw themselves the same way, on the tracks you race.

[![Download on the App Store](https://slicks.app/app-store-badge-white.svg)](https://apps.apple.com/ca/app/slicks/id6746713889?mt=12)[![Download on the App Store](https://slicks.app/app-store-badge-white.svg)](https://apps.apple.com/ca/app/slicks/id6746713889)[hello@slicks.app](mailto:hello@slicks.app)

_Figure: South Garda Karting drawn from the catalog's centreline as an empty track with a north arrow marked and no lap on it._
